[ORDER] ARP Odyssey Mk II/III VCO PCBs/Panels

From circuitbending to homebrew stompboxes & synths, keep the DIY spirit alive!

Moderators: Kent, luketeaford, Joe., lisa

Post Reply
User avatar
mOBiTh
Super Deluxe Wiggler
Posts: 2000
Joined: Sun May 20, 2012 2:20 pm

Post by mOBiTh » Mon Aug 20, 2012 3:28 pm

i'm after a panel too please! 8_)
Top
User avatar
mattrick
Common Wiggler
Posts: 188
Joined: Wed Apr 18, 2012 10:16 pm
Location: Madrid, New Mexico, USA

Post by mattrick » Mon Aug 20, 2012 4:07 pm

2 VCO boards please :tu:
san pedro labs | creative audio electronics | custom synth manufacture
my work: http://sanpedrolabs.com
my music: http://www.soundcloud.com/mattrick
Top
User avatar
frequencycentral
Kicking the shit out of your speakers
Posts: 1185
Joined: Thu Dec 31, 2009 10:49 am
Location: Rick, FC>UK
Contact:
Contact frequencycentral

Post by frequencycentral » Tue Aug 21, 2012 6:33 am

Ok, I'm ready to take orders for this project. Please make your payments by Paypal gift to:

rickholt22@hotmail.com

Please state your MW name, what you are ordering and your address.

I've made a bunch of PCBs already, but still have the bulk to go, so shipping might be a few weeks for tail-end-charlies!
Top
User avatar
brother303
Wiggling with Experience
Posts: 439
Joined: Mon Feb 15, 2010 9:01 am
Location: Ruhr-Area/Germany

Post by brother303 » Tue Aug 21, 2012 9:00 am

Hi,

payment sent!

Cheers
Greg
Peake wrote: DIY is all about the backlog. If you don't have a huge backlog, you aren't trying hard enough.
Top
glitched01
Wiggling with Experience
Posts: 330
Joined: Wed Nov 03, 2010 5:16 pm
Location: US
Contact:
Contact glitched01

Post by glitched01 » Tue Aug 21, 2012 11:27 am

Everything works 100% with 12v? I remember the original was on 15v.
Top
User avatar
frequencycentral
Kicking the shit out of your speakers
Posts: 1185
Joined: Thu Dec 31, 2009 10:49 am
Location: Rick, FC>UK
Contact:
Contact frequencycentral

Post by frequencycentral » Tue Aug 21, 2012 12:28 pm

glitched01 wrote:Everything works 100% with 12v? I remember the original was on 15v.
Ah, so far I have only tested it on my workbench modular which is +/-15V. I'll hook it into my Euro system tomorrow. I'm assuming there will be no issue with +/-12V. Other +/-15V VCOs I've built just needed their scale trimmer tweaked in to track within my +/-12V system.
Top
jaidee
Common Wiggler
Posts: 196
Joined: Wed Jun 10, 2009 8:15 am

Post by jaidee » Tue Aug 21, 2012 12:45 pm

2 VCO plus 1 RM

Thanks!
Top
User avatar
PF
Wiggling with Experience
Posts: 459
Joined: Sat Jan 02, 2010 8:18 am
Location: Sweden/Stockholm

Post by PF » Thu Aug 23, 2012 3:48 am

Payment sent...
If you don´t ask, you don´t get......

Musik
http://www.myspace.com/pouppeefabrikk/music
_______________________________________
Videos
http://www.youtube.com/user/ThePF412
_______________________________________
Record Label
http://www.alfa-matrix.com
amnesia wrote:So I am questioning if I need the Easel. But I bet I buy it being such a Buchla fanboy.
Top
User avatar
steffensen
Veteran Wiggler
Posts: 721
Joined: Tue Apr 07, 2009 2:10 pm
Location: Sweden

Post by steffensen » Thu Aug 23, 2012 3:52 am

frequencycentral wrote:
glitched01 wrote:Everything works 100% with 12v? I remember the original was on 15v.
Ah, so far I have only tested it on my workbench modular which is +/-15V. I'll hook it into my Euro system tomorrow. I'm assuming there will be no issue with +/-12V. Other +/-15V VCOs I've built just needed their scale trimmer tweaked in to track within my +/-12V system.
I believe its been confirmed in the build thread at E-M that it will work fine on +/-12v.
Top
User avatar
LED-man
Super Deluxe Wiggler
Posts: 1524
Joined: Wed Aug 08, 2012 1:48 pm
Location: Wolfsburg Germany
Contact:
Contact LED-man

payment

Post by LED-man » Fri Aug 24, 2012 2:16 am

when is the cutoff time to pay the pcbs ?
Top
User avatar
frequencycentral
Kicking the shit out of your speakers
Posts: 1185
Joined: Thu Dec 31, 2009 10:49 am
Location: Rick, FC>UK
Contact:
Contact frequencycentral

Re: payment

Post by frequencycentral » Fri Aug 24, 2012 3:11 am

LED-man wrote:when is the cutoff time to pay the pcbs ?
Any time is fine. I make them on demand.
Top
User avatar
Dego
Veteran Wiggler
Posts: 748
Joined: Thu Jan 29, 2009 9:22 am
Location: Sweden

Post by Dego » Fri Aug 24, 2012 4:01 am

Has anybody sourced the 1.87K tempco?
Top
User avatar
frequencycentral
Kicking the shit out of your speakers
Posts: 1185
Joined: Thu Dec 31, 2009 10:49 am
Location: Rick, FC>UK
Contact:
Contact frequencycentral

Post by frequencycentral » Fri Aug 24, 2012 4:14 am

Dego wrote:Has anybody sourced the 1.87K tempco?
On the EM thread Andy states that there is enough wiggle in the scale trimmer to accommodate for a 2K tempco. Alternatively, a 28.7K resistor in parallel with a 2K tempco will make a 1.87K tempco (or thereabouts).
Top
User avatar
sicpaul
Wiggling with Experience
Posts: 342
Joined: Thu Dec 22, 2011 9:28 am
Location: Berlin

Post by sicpaul » Fri Aug 24, 2012 5:46 am

Hi Rick,

Paypalled for 2 VCO boards. I did not explicit mention the additional RingMod PCB in payment, hope it will be included allthough.

Fine to see clearly +/-12V operation is possible :razz:

Thanx anyway for doing this run :yay:
Top
User avatar
Dego
Veteran Wiggler
Posts: 748
Joined: Thu Jan 29, 2009 9:22 am
Location: Sweden

Post by Dego » Fri Aug 24, 2012 5:52 am

frequencycentral wrote:
Dego wrote:Has anybody sourced the 1.87K tempco?
On the EM thread Andy states that there is enough wiggle in the scale trimmer to accommodate for a 2K tempco. Alternatively, a 28.7K resistor in parallel with a 2K tempco will make a 1.87K tempco (or thereabouts).
Cool!
Top
User avatar
frequencycentral
Kicking the shit out of your speakers
Posts: 1185
Joined: Thu Dec 31, 2009 10:49 am
Location: Rick, FC>UK
Contact:
Contact frequencycentral

Post by frequencycentral » Fri Aug 24, 2012 6:31 am

sicpaul wrote:Paypalled for 2 VCO boards. I did not explicit mention the additional RingMod PCB in payment, hope it will be included allthough.
EVERYONE gets a Ring Mod PCB, you don't even have to ask.
Top
User avatar
xonetacular
Super Deluxe Wiggler
Posts: 2603
Joined: Mon May 21, 2012 10:35 pm
Location: Boynton Beach, FL, USA

Post by xonetacular » Sat Aug 25, 2012 9:24 pm

2x VCO, 1RM, and 1 panel for me
Top
User avatar
Juxwl
Come for our...uhhh...corn?
Posts: 227
Joined: Fri Nov 25, 2011 1:59 pm
Location: Colorado

Post by Juxwl » Tue Aug 28, 2012 3:19 pm

frequencycentral wrote: EVERYONE gets a Ring Mod PCB
:yay: :banana: :woah: :omg: :love: :party: :chug: :wookie: :domodance: :rock: :nuke:
Image
Top
User avatar
aL Pariah
Common Wiggler
Posts: 120
Joined: Mon Dec 19, 2011 1:51 pm
Location: Stratford upon Avon, England.

Post by aL Pariah » Tue Aug 28, 2012 9:29 pm

Ordered 2 PCBs and a Panel, cheers! :tu:
Top
hv0190
Common Wiggler
Posts: 188
Joined: Fri Sep 10, 2010 1:52 am
Location: Munich

Post by hv0190 » Mon Sep 03, 2012 2:38 am

Back from holiday and paypalled for the 4 PCBs! :bananaguitar:
Top
User avatar
aladan
Desperately Seeking Sondra
Posts: 551
Joined: Tue Feb 14, 2012 12:52 am
Location: Adelaide, Australia

Post by aladan » Mon Sep 10, 2012 6:03 pm

Package of many FC>UK boards received in Oz! :bananaguitar:

:hail: FC>UK :hail:
Top
User avatar
sicpaul
Wiggling with Experience
Posts: 342
Joined: Thu Dec 22, 2011 9:28 am
Location: Berlin

Post by sicpaul » Mon Sep 17, 2012 5:16 am

Hi Rick,

I'm happy looking forward to long soldering sessions ...

In other words
all boards (2ARP VCO, Ringmod, Recycler and Modulation Druid) and PICs arrived in Berlin :yay:

Thanks
Top
Jarno
Super Deluxe Wiggler
Posts: 2814
Joined: Mon Nov 15, 2010 6:34 am
Location: Rosmalen, NL

Post by Jarno » Mon Sep 17, 2012 7:27 am

THIS Is a Panasonic SMT 3300ppm resistor 1.8k, maybe that's acceptable to use instead of the 1.87k (maybe use 680r in series?).
Top
User avatar
steffensen
Veteran Wiggler
Posts: 721
Joined: Tue Apr 07, 2009 2:10 pm
Location: Sweden

Post by steffensen » Mon Sep 17, 2012 7:29 am

Jarno wrote:THIS Is a Panasonic SMT 3300ppm resistor 1.8k, maybe that's acceptable to use instead of the 1.87k (maybe use 680r in series?).
Seems to work, if you do it this way. http://modularsynthesis.com/am/am.htm

Looks pretty darn fiddly however. :)
Top
User avatar
PF
Wiggling with Experience
Posts: 459
Joined: Sat Jan 02, 2010 8:18 am
Location: Sweden/Stockholm

Post by PF » Tue Sep 18, 2012 9:19 am

Got my boards....
If you don´t ask, you don´t get......

Musik
http://www.myspace.com/pouppeefabrikk/music
_______________________________________
Videos
http://www.youtube.com/user/ThePF412
_______________________________________
Record Label
http://www.alfa-matrix.com
amnesia wrote:So I am questioning if I need the Easel. But I bet I buy it being such a Buchla fanboy.
Top
Post Reply

Return to “Music Tech DIY”