Seems these modules have vaporized. Bummer.

Got it working. It was a bad screen.

Hello all! Finished my build and nothing is showing up on the screen. When I press the middle button between the LEDs the two leds light up depending on where I turn the center pot. Where should I look to fix this? Edit: I'm also getting outputs on both L and R. It does sound like it's a very low oc...

What connector should I use to plug it in to use the jack lights?

Question for assembly: do I need to use 1206 resistors for R1 and R3 or can I use 0805?

Nvm! It was IC 9. Reflowed it and all good now. But boy are those leds bright!

Hello team!

I just put together a Euclidean Circles V2 and one of the ring leds are coming on. The G button and all 3 encoders light up and change when pressed.

Where can I look to see why the LEDs are working? I made sure to align the notches in each one, btw..

Thanks in advance!

Question: I just built a module and not understanding what the Vref is supposed to do. Either way I flip the switch nothing happens on any of the outputs and with the sliders in all positions.

Any help would be appreciated. Thanks!

I've tried just about everything to get my device to upgrade, but no luck. The farthest it gets is 16 seconds then the darn flashing red lights. Things I've tried: 1) direct from my phone 2) direct from my laptop 3) phone/laptop into Doepfer A-119 at all gain levels 4) phone laptop into Streams (as ...

That did it! Seems to be working and I'm off to test the outputs now.

Thanks again. Sometimes all you need is another set of eyes.

Here are photos of the PCBs.

Just finished a build. Did the tests, all good. Plug it in..... and nothing. No Display lights, no button, lights,... Nothing.

I went through the entire 2 boards and reflowed all joints, and verified polarity.

Parts were bought using the Mouser cart that was provided.

Just finished a build. Did the tests, all good. Plug it in..... and nothing. No Display lights, no button, lights,... Nothing.

I went through the entire 2 boards and reflowed all joints, and verified polarity.

Parts were bought using the Mouser cart that was provided.

Oh yeah! Let's get it going! Any updates?

I'm building a Sum2 right this moment. Just waiting on a few hard to get dual pots and then I'll fire it up. In the meantime, the pcb and panel are great and the only issues I have is the lettering on the pcb is a bit fuzzy and the ordering of the part numbering is kind of all over the place which m...

Just got my board in last week and have had the parts lying around for a bit. I'll probably start the build sometime later this month and I'll make sure to post any questions here.

Thanks!

Have these builds become obsolete or are they still worth pursuing?

Oohhhh man! Looking forward to it!

Are any of the DIY kits available??? I've been hunting these down for months and can't find anything.

Any word on when the kits will be in stock again? My fingers are itching to get them on this module.

Altitude909 wrote: ↑

Thu Aug 20, 2020 11:42 am

correct

Worked like a charm. Thank you!

Ok, I have the extra pin connected to the Teensy.

And I need to connect the square pad to the middle pad of the 3 pin header towards the bottom of the board?

Thanks for the reply.

Just finished a build of a utemps version, loaded the firmware, started up, got into calibration, but no output on 4/D.

I power cycled it and ran a clock into it and got pulses out of all of the outputs except for 4/D.

Any help would be appreciated.

Thanks!

I just finished a build, flashed the software to it, and it starts up great, but the issue is when I'm calibrating it.

There is no voltage coming out of 4D. Is there something I should look at?

Thanks!

Tune your VCO's to different musical intervals, send your quantized output from Rene to a buffered multi then to each voice, then your trigger from Rene to Marbles (or similar) and the trigger outputs to each voice to have them trigger randomly adding voices.