some thoughts: i love the mk3. i love the mk2 as well, but mk3 is like a whole different thing really. still, they sit side by side. the routing options are vast, i personally like the stereo routing and the series routing the best and use both fairly often. the 4 pole mode sounds especially fierce ...

piston hondas mk1 and 2 stuck between wavetables in the additive banks

As stated you're looking for a scanner. Synapse would give the most options. It's great and someone recently described it as the Maths of mixer/switches. yeah that we me, and i stand by it. synapse rips. https://www.muffwiggler.com/forum/viewtopic.php?f=74&t=229657 yes you can only crossfade betwee...

well ok wait, so should i be calibrating at x1 and trying to zero in on 480? or should i be calibrating at /4 and zeroing in on 120?

also according to the manual, it'll go down to 30..

witchonhorseback wrote: ↑

Sun May 03, 2020 4:41 pm

I used the SHMk2 and yes, this gives you 480. It was very hard to calibrate it precisely, though; it kept drifting a few tenths of a point in each direction. Is this normal?

yeah i had the drift too, i just tried to let go of the buttons whenever it zero'd in on 120 exactly

its not really 'cool' anymore, but the stillson hammer mk1 is super versatile and very playable. i like to spit out the burst outputs into a bipolar mixer then 'sequence' things like speed and sample rate controls on sampler/looper type modules for some sped-up-slow-down weirdness, or triggering mul...

can't believe i missed this. i guess i was just scanning for vowel and the idea of 'chorale' was even on my mind. thanks!!

@igorrr similar to delay vowel, would a reverb vowel be possible?

re-vowel, as it were

has anyone successfully calibrated the clock?

if i feed the tempo jack with 120BPM from the SHmk2 clock out, kermit reads ~480BPM, even though i have kermit's global div set to x1...but if i set it /4 only then can i get it around 120...am i missing something?

this seems a treat..

rikrak wrote: ↑

Mon Apr 20, 2020 10:10 pm

Would you mind sharing the type of knob you used. I did a search on Thonk earlier, but wasn't sure what I was looking for to be compatible with the shafts.

https://modularaddict.com/micro-knobs

igorrr, do you have an idea of when the module might be available again in the US? ETA from analoguehaven is "soon" more or less It's been at "soon" since the first week of March. On 3/20 they were already shipped by Happy Nerding, idk.. well, i'm not gonna post shawn's email word for word here, bu...

Anyone else notice the module "goes to sleep" after a few hours....tap indicator goes off and status lights of Osc C & D go glacial. No way to wake it up....just have to reboot. Came here to ask the same question. This is happening every time I use it. Same thing happens to me if i leave my rack on...

witchonhorseback wrote: ↑

Tue Apr 14, 2020 6:58 am

igorrr, do you have an idea of when the module might be available again in the US?

ETA from analoguehaven is "soon" more or less

Then OSC C: Again slowly turning up AMPLITUDE by hand, then playing around with the FREQUENCY knob, no modulation assigned on Oscillator C. Then, after a short parameter jump due to switching knob C from FREQUENCY to AMPLITUDE slowly turning AMPLITUDE on oscillator C back down again. Now the steps ...

One question to other users the internal modulation (57:40): I get unpleasant digital clicks when I use internal envelope modulation of oscillator amplitude, especially in unison mode. In the video though (from 1:01 on) he sets the oscillator to unison and it sounds quite good - in my rack I have t...

had some downtime today, and spent a little time putting kermit through its paces and grabbed a snapshot of what ended up happening. https://soundcloud.com/jshmason/untitled-xiv as best i can remember, 3 separate sequences from stillson hammer mk2 feeding a piston honda mk1, donut mk2 (both primary ...

robotopsy wrote: ↑

Thu Mar 12, 2020 10:03 pm

Nice collection
This Double Andore v1 needs some new orange knobs

Sinamsis wrote: ↑

Thu Mar 12, 2020 6:58 pm

I couldn't resist and got a second Kermit mk III, I have to take one of my older Kermits out of the case (but still kept one!).

mine are so tight on my DAmk1, i'm afraid i'm gonna rip the pot shaft off..

rather than create a new thread - seeing as i have a related + auxillary question: besides the greater ma of the PSU3....do either of these perform bettr than the other when it coms to sound quality? i cant imagine doepfer creating a psu with poor audio...but im curious as i'd like to pull the trig...

The thing just landed...having a blast running radio through the audio in. FM knob behaves exactly like the fine tune knob when nothing plugged in. :roll: what fw is it running? i think that was addressed on 2.5.1 v2.5.1 - June 17, 2016 - Reduced noise on FM input when no cable is plugged in.

batumi is basically the way to go here (as a batumi user, imo)

another idea, is two eowave zone bf's — 4 variable wave lfos w/ sync in 10 hp

Pighood wrote: ↑

Thu Mar 05, 2020 11:41 am

Are there instructions on how to load the update? Can it be done via the micro SD card?

nope, it's still done pickit3 style...instructions are in a readme file included with the fw

yeah the ch d button combos are a little more difficult, but on the whole, i was surprised how quickly the whole menu became muscle memory. i still get hung up sometimes when i adjust a virtual attenuator, then forget and twist the associated knob and end up in left field (though sometimes thats fun...

If there is a bit of spare time, it would be great to know if the preset sequencer works reliable when unison mode is engaged. i can check this out when i get home today, unless someone else beats me to it...though i'm not 100% sure if i follow what you are looking to know. the unison setting is st...

Leverkusen wrote: ↑

Sun Mar 01, 2020 3:49 am

There also were a few points though where I had a feeling that the firmware is not quite there yet. For example does the internal amplitude modulation does not work in code scan mode?

can confirm internal modulation does work on amplitude in code scan mode